Guangzhou DSPPA Audio Co., Ltd.
Products
Contact
Email: export@dsppa.com
Tel: 020-28346138
Fax: 020-81305947

MAG6416Ⅱ 32-channel Fire Linkage Module

Features

● This module is the interface between network PA system and fire center.;
● When receiving the alarm signal sent by the fire center, it will activate the network PA system corresponding working area automatically and enter the override status of the emergency broadcasting;
● Each machine has 32 fire trigger channels, and each channel alarm zone can be any combination through the host setting;
● Each alarm channel includes routing fault detection function, and can troubleshooting system line automatically;
● The same system can have multiple machines connected to the network, and can extend control area at random.

  • Introduction
  • Specification

MAG6416Ⅱ 32-channel Fire Linkage Module

1.Setup indicator

When the parameters of this module cannot be found, (such as IP is not clear) press the Mode button. The indicator will light.

2.Alarm signal input interface

CH1-CH9,1 channel to 9 channel for alarm signal input interface, COM for common terminal

3.Alarm signal input interface

CH10-CH18,10 channel to 18 channel for alarm signal input interface, COM for common terminal

4.Dip switch

Mode: When the parameters of this module cannot be found, (such as IP is not clear) press the Mode button.The indicator will light, and the machine parameters restore the following specific parameters:

IP:192.168.16.2GATE:192.168.16.1Mask Code:255.255.255.0

Main server IP:192.168.16.250  Standby server IP:192.168.16.251

After setting, dialmodeto restore the previous configuration.

Note: In the same network only one machine of the same type can be setmode, otherwise it will have IP conflict.

Check: Line detection enable to switch. The machine has a 32-channel line fault detection function, dial the switch to open the line detection (channel independent switch setting refer to the fourth section "fire channel line detection function configuration"). If you want to use line detection,the channel which needed to open the line detection need to need to configure the 47K pull-down resistor box.

Note: When the module issued a drop of sound is relatively long, indicating that the external line is not connected, when the issue of the sound is more rapid, indicating that is the alarm sound.

H / L: When theinput logic setting switch is set toH, it is the level trigger mode; when thesetting switch is set to L, it is short-circuit trigger mode.

5.Alarm signal input interface

CH19-CH27, 19-channel to 27-channel alarm signal input interface, COM is common.

6.Alarm signal input interface

CH28-CH32, 28-channel to 32-channel alarm signal input interface, COM is common.

Note: Alarm signal input interface can be input with a positive polarity signal of 5V-24V or the short circuit signal of 0Ω-5K impedance.

7.SC1、SC2 short circuit output

As long as there is an alarm signal input (any one or more), SC1, SC2 short circuit output.

8.485 communication interface

A, B for the RS485 communication interface. It can be used to communicate with other third party systems to implement alarm triggers (using this function has to contact our technical staff).

485 protocol format:

Frame header + source address + destination address + frame number + length + function code + data + check code

The header is FE FC

Source address, destination address, frame number, function code for 1 byte, length, check code for 2 bytes, higher one is in front and the length does not contain the header

The generator polynomial of the CRC check is: X16 + X15 + X2 + 1

The address of this alarm module is: 0xFE

Function code meaning:

0x66 set all zones alarm, followed by 32 bytes of data, data 0 indicating that the alarm revoked, 1 for alarm

0x67 set a single zone alarm, followed by a byte channel number and a byte of state data, channel number 0-31 for 1-32 channel, the alarm state values are the same as above.

9.Network indicator

When the module drops the indicator lights green; when the module is connected successfully via the network,the indicator lights red.

Package Dimension

190×40×230mm

Machine Dimension

173×23×210mm

Gross Weight

1.5kg

Net Weight

1.0kg

Relate Products

  • POE1028 SNR Self-adaptive PoE Network SensorPOE1028 SNR Self-adaptive PoE Network SensorJuly 28, 2020The device will automatically adjust the volume of the broadcast sound to make it larger than the on-site ambient sound; otherwise, when the on-site ambient sound is detected too much smaller than the...view
  • MAG6411 Audio Acquisition ModuleMAG6411 Audio Acquisition ModuleJune 9, 2021MAG6411 Airport Broadcast Audio Acquisition Module is a network all-digital analog and digital converter signal processor based on TCP/IP transmission protocol. Local program, background music, voice ...view
  • MAG6832 2 Channels Streaming Media InterfaceMAG6832 2 Channels Streaming Media InterfaceNovember 10, 2021This device is a streaming media interface that supports AirPlay, DLNA, Internet radio and other functions at the same time. All mobile phones (IPHONE) and tablets (IPAD) that support AirPlay can be c...view
Leave a Message Email Us

we will contact you within 24 hours.

Related News
  • Tel:+86 020 37166520
  • Email:export@dsppa.com
  • Address:No.1 Xiahe Rd, Jianggao Town, Baiyun District, Guangzhou, Guangdong, China